Cesta  |  Contacto  |  Ayuda  |  Envíe un correo  | 
En Chile 800-395-179
Fuera de Chile001-203-978-7240

OMEGA/HBM Strain Gages | High Temperature and Resistance to Alternating Loads

HBM-M-Series

High Temperature Strain Gages | HBM Strain Gages | OMEGA | HBM-M-Series
Nuevo!

High Temperature Strain Gages | HBM Strain Gages | OMEGA

Ver Todas los Modelos Abajo

  • High Resistance to Alternating Loads
  • High Temperature Range 300°C (572°F)
  • Wide Spectrum of Different Types

Descripción

M Series strain gages have been specially developed for high resistance to alternating loads at increased strain levels and high temperatures up to 300°C (572°F). They are foil strain gages with measuring grids made of a special nickel-chromium alloy. OMEGA/HBM offer this special strain gage with various geometries, measuring grid lengths and temperature response matching.

New materials offering high strength such as fiber composites pose a major challenge for strain gages used for measurements specifically when pushing components to their mechanical limit of performance. Situations may arise where a strain gage subjected to alternating loads at increased load levels is weakened and fails earlier than the component under test. The M Series has been specially developed for high resistance to alternating loads and allows for testing of materials featuring high strength.

All M Series strain gage types are available with different measuring grid lengths:
    • 1.5 mm: where space is a constraint or when highly selective measurement results are required
    • 3 mm: for inhomogeneous materials and where space is a requirement or not
    • 6 mm: for inhomogeneous materials and where space is not a requirement

The right measuring grid length: The measuring grid length depends on the aim of measurement, since the result of a measurement with strain gages will be determined as the average of strains. In general, measuring grid lengths of 3 to 6 mm (0.06 to 0.24") generates a better result.

Long measuring grids are recommended where there is an inhomogeneous material such as concrete or wood. A long strain gage will bridge the inhomogeneity of the work piece and return the strain underneath the measuring grid as the measurement result.

Short measuring grids are suitable for detecting a local strain state. Therefore, they are suitable for determining strain gradients, the maximum point of notch stresses and similar stresses.

Specifications
Strain Gage Construction–Foil Strain Gage
Carrier:
    Material:
Glass fiber reinforced phenolic
    Thickness: 35 ±10 µm
Grid Foil:
    Material: CrNi
    Thickness: 5 µm
Encapsulation:
    Material: Polyimide film
    Thickness: 25 ±5 µm
Connections: Solder pads with strain relief
Resistance: 350 and 1000 Ω
Resistance Tolerance: ±0.3%(1)
Gage Factor: Approximate 2.2 (specified on each package)
Gage Factor Tolerance: ±1.5% (for grid length <3 mm) ±0.7% (for grid length ≥3 mm)
Temperature Coefficient of the Gage Factor: Specified on each package
Transverse Sensitivity: Specified on each package
Operating Temperature Range: -200 to 300°C (-328 to 662°F)
Temperature Response (Ferrite Steel): 10.8 ppm/K (6.0 ppm/°F)
Maximum Elongation:
    Positive Direction: 10,000 µm (1%)
    Negative Direction: 15,000 µm (-1.5%)
Minimum Bending Radius: 5 mm (0.20") for linear gages 10 mm (0.39") for stacked rosettes
Bonding Material that Can Be Used: Z70 or EP310S
Fatigue Life (Test to Failure):
    107 cycles at 2000 µm/m
    106 cycles at 2200 µm/m
    104 cycles at 3100 µm/m
Hacer Pedido(Especifique el Número de Modelo)
Número de parte/Desc.
Cant.
Descripción
For dimensions refer to "To Order" table in Specs
All models below are 350Ω Nominal Resistance
LM1: Linear strain gage with one measurement grid measuring strain in one direction
Quick Ship
1-LM11-1.5/350GE
USD$170.00
Disponible en: 12 Semanas
 
10 pack, Voltage 7
Quick Ship
1-LM11-3/350GE
USD$170.00
Disponible en: 12 Semanas
 
10 pack, Voltage 11
Quick Ship
1-LM11-6/350GE
USD$175.00
Disponible en: 12 Semanas
 
10 pack, Voltage 16
TM1: T rosette with two measurement grids, offset by 90° measuring tension and compression
Quick Ship
1-TM11-1.5/350GE
USD$200.00
Disponible en: 12 Semanas
 
5 pack, Voltage 7
Quick Ship
1-TM11-3/350GE
USD$200.00
Disponible en: 12 Semanas
 
5 pack, Voltage 11
Quick Ship
1-TM11-6/350GE
USD$205.00
Disponible en: 12 Semanas
 
5 pack, Voltage 22
TM9: Stacked T rosette with two measurement grids, offset by 90° measuring tension and compression
Quick Ship
1-TM91-1.5/350GE
USD$265.00
Disponible en: Disponible
 
5 pack, Voltage 5.8
Quick Ship
1-TM91-3/350GE
USD$265.00
Disponible en: Disponible
 
5 pack, Voltage 10
Quick Ship
1-TM91-6/350GE
USD$270.00
Disponible en: 12 Semanas
 
5 pack, Voltage 14
XM4: V-shaped strain gage with two measurement grids, arranged at ±45° to the axis determination of shear stresses
Quick Ship
1-XM41-1.5/350GE
USD$215.00
Disponible en: 12 Semanas
 
5 pack, Voltage 5.4
Quick Ship
1-XM41-3/350GE
USD$220.00
Disponible en: 12 Semanas
 
5 pack, Voltage 10
Quick Ship
1-XM41-6/350GE
USD$225.00
Disponible en: 12 Semanas
 
5 pack, Voltage 17
RM8: Rectangular strain gage rosette with three measurement grids at 0°/45°/90° biaxial stress state with unknown principal stress direction
Quick Ship
1-RM81-1.5/350GE
USD$265.00
Disponible en: Disponible
 
5 pack, Voltage 7
Quick Ship
1-RM81-3/350GE
USD$265.00
Disponible en: 12 Semanas
 
5 pack, Voltage 11
Quick Ship
1-RM81-6/350GE
USD$270.00
Disponible en: Disponible
 
5 pack, Voltage 16
RM9: Stacked strain gage rosette with three measurement grids at 0°/45°/90° biaxial stress state with unknown principal stress direction
Quick Ship
1-RM91-1.5/350GE
USD$325.00
Disponible en: Disponible
 
5 pack, Voltage 5.3
Quick Ship
1-RM91-3/350GE
USD$325.00
Disponible en: Disponible
 
5 pack, Voltage 9.3
Quick Ship
1-RM91-6/350GE
USD$330.00
Disponible en: 12 Semanas
 
5 pack, Voltage 13
Accessories
Quick Ship
1-EP310S
USD$210.00
Disponible en: 12 Semanas
 
High temperature adhesive; two-component epoxy resin adhesive
Todos los productos en este sitio se muestran en la moneda de EE.UU.
NOTA: † Maximum permitted effective excitation voltage specified for steel material.

Instructions for Use of Accessories shown under Product Manuals below.

All listed adhesives are specifically designed/approved to be used for the new M Series of strain gages.

Safety Data Sheets for Accessories can be found (without "1-" Part Number prefix) at omega.com, Support, MSDS.

Generador de Número de Parte

Generador de Número de parte
Descripción de Opciones:


(1) Geometries seleccionar de:
LM1 para Linear strain gage with one measurement grid
TM1 para Stacked T rosette with two measurement grids
XM4 para V-shaped strain gage with two measurement grids
RM8 para Rectangular strain gage rosette with three measurement grids
RM9 para Stacked strain gage rosette with three measurement grids

(2) Measurement Grid mm(inch) seleccionar de:
1.5 para Measurement Grid A 1.5 (0.06)
3 para Measurement Grid A 3 (0.12)
6 para Measurement Grid A 6 (0.24)
NOTA: No todas las combinaciones pueden no ser válidas, compruebe la hoja de especificaciones para números de parte válidos.

Manuales de Productos:

Descargar Rapid Adhesive (English/German/French)
Descargar Two-component Epoxy resin adhesive (English/German/French)
Descargar Accelerator for Z70 adhesive (English/German/French)